Barco MatrixPRO Manuel d'instructions Page 75
- Page / 90
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
MatrixPRO • 16x16 and 8x8 HD/SD-SDI Router • User’s Guide 65
_K==oÉãçíÉ=`çåíêçä=mêçíçÅçä
MatrixPRO Remote Commands
j~íêáñmol=oÉãçíÉ=`çãã~åÇë
The table below lists MatrixPRO remote commands. Click the hyperlink for detailed
descriptions and examples.
Table B-4. MatrixPRO Remote Commands
Command Description
HELP Capabilities. Send complete list of commands available in ASCII format
CLEAR
Clear all matrix video routings
CSUMSTAT
Display Main Code/RBF Checksum info
FPLOCK en
Locks/unlocks Front Panel control
GADD grp out in
Add an output or input to group
GCLEAR grp
Clears grouping information
GDEL grp out in
Remove output, input from group
IPCONFIG I3 I2 I1 I0
IP address configuration I3.I2.I1.I0
ISTAT num
Input video status
LOADRMP
Places unit into loader mode for firmware upgrade
OBLNK out blnk
Displays output channel status
OSTAT
Displays output status in ASCII
PRST num
Saves current front panel configuration to a Preset location
PSTAT
Displays preset status in ASCII
RCLKEN num en
Enables/Disables individual output reclockers
RESETMP op
Reset MatrixPRO, recall saved Flash values op [R|F] Reset|Factory Reset
RNOV
Recall Flash settings
RPRST num
Recall preset from a Preset location
RTEMP out in
Route inputs to outputs. If output is in group, group is routed too
SBAUD mode
Sets Baud Rate. 0=19200, 1=28800, 2=38400, 3=57600
SMODE mode [485id]
Serial Mode. 0=RS232, 1=RS485. [485id] opt if RS232
SWITCH mode
Switching Mode. 0 = (Vertical Interval Switching Off), 1 = On
TAKE en
en = 1 simulates a TAKE button pushed on the front panel (i.e takes all preliminary
routes and makes them permanent). en = 0 simulates a CANCEL button pushed
UNOV
Save current settings to FLASH
- • Manual # 26-0401000-00 1
- • Revision A 1
- • June 29, 2005 1
- `çéóêáÖÜí 2
- ^sboqfppbjbkq> 5
- `Ü~åÖÉ=eáëíçêó 6
- Table of Contents 10
- NK==fåíêçÇìÅíáçå 11
- `Ü~éíÉê=píêìÅíìêÉ 12
- `çåîÉåíáçåë= 13
- ^Äçìí=íÜÉ=j~íêáñmol 14
- OK==e~êÇï~êÉ=fåëí~ää~íáçå 17
- 2. Hardware Installation 18
- PK==léÉê~íáçå 23
- `çåíêçä=lîÉêîáÉï 24
- 3. Operation 25
- To change brightness: 31
- To adjust the IP address: 32
- Take key 34
- To save presets: 36
- > File 1 37
- • Control GUI Installation 41
- • Equipment Setup 41
- • Remote Ethernet Setup 41
- • GUI Operation 41
- `çåíêçä=drf=fåëí~ää~íáçå 42
- GUI Operation 56
- • Connectivity Diagram 57
- `çååÉÅíáîáíó=aá~Öê~ã 58
- SK==réÖê~ÇáåÖ=pçÑíï~êÉ 59
- `çååÉÅíáåÖ=íç=_~êÅç=cçäëçã= 61
- 6. Upgrading Software 62
- ^K==péÉÅáÑáÅ~íáçåë 65
- `çããçå=péÉÅáÑáÅ~íáçåë= 68
- _K==oÉ ã çíÉ=`çåíêçä=mêçíçÅçä 69
- _K==oÉãçíÉ=`çåíêçä=mêçíçÅçä 70
- `prjpq^q 76
- `K==` çåí~Åí=fåÑçêã~íáçå 83
- `K==`çåí~Åí=fåÑçêã~íáçå 84
Produits connexes et manuels pour Mise en réseau Barco MatrixPRO
(88 pages)Whirlpool AKZM 834/IXL podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Akcesoria do mikserów / robotów kuchennych Whirlpool AKZM 834/IXL.
Dostarczamy 2 pdf podręczników Whirlpool AKZM 834/IXL do pobrania za darmo według typów dokumentów: Instrukcja Obsługi
Commentaires sur ces manuels