Barco CORONIS MFGD 3621 Manuel d'utilisateur

Installation & User Manual Supported displays: MFGD 2621, MFGD 3621Coronis 21-inch

Preface10Disposal InformationThe lamps inside the display contain mercury. Do not throw the display in the trash. Dispose of it as required by local o

General tips100Problems and solutionsProblem description Possible tests or solutionsScreen remains black • Please check the installation procedure in

General tips101No image during PC start-up• Check the VGA jumper settings on the display controller• Check the CMOS settings in the PC BIOSNothing hap

General tips102Setting the resolution of your CORONIS displayNote: In order to set the resolution of your CORONIS you must be logged in using an acco

General tips103working with by right clicking on the rectangle that represents it, deselect “Attached” and click the “Apply” button.Note: Since Windo

General tips104Note: If you have a single display configuration and you have enabled DualView, Windows will not allow you to attach the second head.

105Technical Information

Technical Information(This page intentionally left blank.)106(This page intentionally left blank.)

Technical specifications107Technical specificationsMFGD 2621:Item SpecificationPicture panel 21.3-inch diagonal viewable screen TFT (thin film transis

Technical specifications108MFGD 3621:Power source Input for 12 VDC power supply unit: 90 ~ 264 VACInput for display: 12 VDC. (The supplied 12VDC power

Technical specifications109Native color resolu-tion8 bits / sub-pixelLuminance 500 cd/m² (calibrated)Contrast ratio 700/1 (typical in dark environment

Safety Instructions11Safety InstructionsGeneral RecommendationsRead the safety and operating instructions before operating the display. Retain safety

Technical specifications110Altitude 7500 m storage3000 m operationItem Specification

Connector pin assignments111Connector pin assignmentsDVI connector:Figure 30: DVI connector pin layoutPin no. Signal Pin no. Signal1 TMDS DATA 2- 14 +

Glossary112GlossaryCalibrationEach display is calibrated in the factory before it is sent to the customer. After this calibration, black and white lum

113Warranty Statement

Warranty Statement(This page intentionally left blank.)114(This page intentionally left blank.)

Warranty Statement115ARTICLE 1: SERVICESBarcoView warrants that the equipment will be free of defects in workmanship or material for the warranty peri

Warranty Statement116ARTICLE 2: ITEMS EXCLUDED FROM WARRANTYThe warranty described herein shall not include the following:2.1 Any hardware or software

Warranty Statement117agents, employees, or representatives, shall be borne by the Customer at its additional cost and expense.3.3 The customer is resp

Warranty Statement118this agreement is impeded by reason of force majeure. For the purposes of this clause the expression “force majeure” means, but s

www.barco.comB4100519-03March 2007

Safety Instructions12code: Green-and-yellow: Earth (safety earth), Blue: Neutral, Brown: LinePower cord with ANSI 73.11 plug: The wires of the power c

Safety Instructions13Operating precautions: How to avoid image retentionContinuous operation of the display with the same image may result in some ima

Explanation of symbols14Explanation of symbolsSymbols on the display and / or power supplyOn the display or power supply, you may find the following s

Explanation of symbols15Symbols used throughout the manual:Warning CautionImportant notice or remarkNoteHint, tip Additional information

Explanation of symbols(This page intentionally left blank.)16

17Introduction

Introduction(This page intentionally left blank.)18(This page intentionally left blank.)

Overview19OverviewThank you for choosing Barco.Single display or complete system?This manual describes installation and usage of a complete system. A

(This page intentionally left blank.)2(This page intentionally left blank.)

BARCOMED CORONIS display controller overview20BARCOMED CORONIS display controller overviewThe BarcoMed Coronis display controller delivers a quality i

BARCOMED CORONIS display controller overview21Supported resolutions for each head of the BARCOMED CORONIS display controllerCoronis 2MP displays• 1200

BARCOMED CORONIS display controller overview22Barco displays overviewBarco displaysThe MFGD 2621 is a 21-inch grayscale LCD display with a native res

BARCOMED CORONIS display controller overview23Tilt & swivel baseThe versatile tilt & swivel foot allows to use the display for viewing portrai

Package contents24Package contentsCoronis System packageEach Coronis system contains one or more display boxes (see below) and a system accessory box

Parts, controls and connectors25Parts, controls and connectorsFrontFigure 1: Front side1. Power LEDThe LED is off when the display is disconnected fro

Parts, controls and connectors26RearFigure 2: Rear side1. Connector compartment coverTo get access to the connectors, remove the cover by pulling down

Parts, controls and connectors27Connect the external power supply, delivered with the display, to this connector.9. Tilt & swivel foot clipThe dis

Parts, controls and connectors(This page intentionally left blank.)28

29Display controller installation

3Copyright noticeThis document is copyrighted. All rights are reserved. Nor this document, nor any part of it, may be reproduced or copied in any fo

Display controller installation(This page intentionally left blank.)30(This page intentionally left blank.)

BARCOMED CORONIS display controller installation31BARCOMED CORONIS display controller installationCaution: Wear a grounded, protective ESD strap durin

BARCOMED CORONIS display controller installation32Figure 4: VGA Jumper Enlarged ViewUsing the VGA capabilities of the BarcoMed CoronisPrior to install

BARCOMED CORONIS display controller installation33Figure 5: PCI and RAID Controller SlotsInstall the BarcoMed Coronis controller in your computer foll

BARCOMED CORONIS display controller installation34DVI cable. For a dual-headed BarcoMed Coronis setup, connect the secondary display to the other con

BARCOMED CORONIS display controller installation35BarcoMed PCI Express® ControllersDuring the first quarter of 2006 Barco Medical Imaging Systems adde

BARCOMED CORONIS display controller installation(This page intentionally left blank.)36

37Display installation

Display installation(This page intentionally left blank.)38(This page intentionally left blank.)

Installation precautions39Installation precautionsPrecautions• Keep your original packaging. It is designed for this display and is the ideal protecti

4(This page intentionally left blank.)

After unpacking the display40After unpacking the displayImportant:In the factory, the height-positioning system in the display foot is blocked with a

After unpacking the display41Adjust the panel orientationYou can change the orientation of the panel at any time, but it is more convenient to select

After unpacking the display42Figure 11: Tilt the panel before rotating3. To change from portrait to landscape, turn the panel counterclockwise.Figure

After unpacking the display43• In a Coronis system, the image orientation will adapt to the new panel orientation automatically after a second.• If th

Power connection44Power connectionTo connect the power:Figure 13Figure 141. To get access to the connectors, remove the connector compartment cover by

Video connection45Video connectionConnecting DVI cables: One display:Figure 151. Connect one end of the DVI cable to the DVI input of the display.2. C

USB connection46USB connectionThe USB connection allows you to use the display as USB hub, to which you can connect USB devices, such as a keyboard, m

Cable routing47Cable routingRouting the signal cables• Bind the cables in the connector compartment together with the cable tie inside the connector c

Cable routing483. Slide the cover upward while moving the lower side of the cover towards the foot.4. Press the cover to the foot so that it makes a c

Attaching the display to an arm stand49Attaching the display to an arm standThe panel, standard attached to the tilt & swivel foot, is compatible

Table of Contents5Table of ContentsPreface ... 7Safety I

Attaching the display to an arm stand506. Remove the four screws fixing the foot while supporting the foot.7. Attach the arm stand firmly to the panel

51Display controller software installation

Display controller software installation(This page intentionally left blank.)52(This page intentionally left blank.)

Display controller software installation53Installing the BARCOMED display controller drivers and softwareNote: The installation dialog will display in

Display controller software installation54c) Click Browse and browse to the root directory of the BARCO MEDICAL IMAGING DISPLAY SYSTEM CD-ROM and clic

Display controller software installation5513. When the driver setup is complete, click the Finish button.The Barco Product Installation Wizard will no

Display controller software installation56Command line (Silent) Install of Drivers and SoftwareSpecifying the silent install option causes most of the

Display controller software installation57Figure 21

Display controller software installation(This page intentionally left blank.)58

59Settings for optimal display performance throughout the product lifetime

Table of Contents6Advanced Properties ... 67Device details ...

Avoiding image retention60Avoiding image retentionImage retention (image sticking, ghost image) is the phenomenon where an image, or a part of it, see

Avoiding image retention61To activate appropriate screen saving, proceed as follows:1. In the display OSD menus, open the Settings menu and switch DPM

Avoiding image retention(This page intentionally left blank.)62

63Display controller tools

Display controller tools(This page intentionally left blank.)64(This page intentionally left blank.)

BarcoMed control panel operation65BarcoMed control panel operationThis chapter describes how to configure the displays in your Barco Medical Imaging D

BarcoMed control panel operation66Figure 22 Barco TabBarco System ReportThe Barco System Report, also known as BarcoMed SelfExam, is a wizard based to

BarcoMed control panel operation67Advanced PropertiesTo access the advanced properties configuration pages for your Barco display controller(s), click

BarcoMed control panel operation68applications that are designed to work correctly with 8-bit (256-color) modes should continue to work normally.Note:

BarcoMed control panel operation69while maintaining compatibility with the Windows graphics device interface (GDI). DirectDraw is enabled by default.M

7Preface

BarcoMed control panel operation70Disable RGB To Static Gray Color TranslationSelect Disable RGB To Static Gray Color Translation if you wish to have

71Display operation

Display operation(This page intentionally left blank.)72(This page intentionally left blank.)

Display operation73Display operationOperating precautionsContinuous operation of the display with the same image may result in some image sticking on

Display operation74About the On-Screen Display (OSD)About the on-screen displayThe on-screen display (OSD) has a hierarchical tree structure, with sev

Display operation753. To exit from a menu, rotate the control wheel to select EXIT and press the control wheel shortly. If you exit from the Main Menu

Display operation764. Rotate the control wheel to select User Controls.5. Press the control wheel to switch from “On” to “Off”.6. Exit the menus.To en

Display operation77Complete OSD overviewMain menuLuminanceLuminance Target adjusts the overall luminance (light output) of the display. It does not af

Display operation78SettingsInformation Name DescriptionDPMS Switch on/off the automatic power saving sys-tem (DPMS)Power LED Switch the power LED on/o

Advanced display operation79Advanced display operationIntroductionImportantThe functions described in this chapter are intended for trained service st

Preface(This page intentionally left blank.)8(This page intentionally left blank.)

Advanced display operation80Advanced functions in the Luminance menuManual BacklightThis function allows to manually control the backlight luminance.

Advanced display operation81DVI LinkClick to switch between single link (Single) and automatic detection of single or dual link (Auto).StabilizerClick

Advanced display operation82FirmwareThe Firmware information menu contains the following items:RuntimesRuntimes is a submenu from General Information

Advanced display operation83MeasurementsScan measurementsName DescriptionInternal Temperature The temperature measured inside the dis-playSensor Tempe

Advanced display operation84Advanced functions in the Adjustments menuIn Advanced mode, the main menu contains an additional menu, Adjustments. This m

85MediCal Pro software

MediCal Pro software(This page intentionally left blank.)86(This page intentionally left blank.)

MediCal Pro installation and operation87MediCal Pro installation and operationMediCal Pro software installationInstall MediCal Pro on the PC. Follow t

MediCal Pro installation and operation(This page intentionally left blank.)88

89Cleaning instructions

Preface9NoticeAlthough every attempt has been made to achieve technical accuracy in this document, we assume no responsibility for errors that may be

Cleaning instructions(This page intentionally left blank.)90(This page intentionally left blank.)

Precautions91PrecautionsPrecautions• Take care not to damage or scratch the glass or LCD panel.• Do not apply pressure on the glass or LCD panel.• Do

Front glass92Front glassProceed as follows:• Clean the glass using a soft cotton cloth, lightly moistened with plain water.• Wipe dry with a dry cloth

Cabinet93CabinetProceed as follows:• Clean the cabinet using a soft cotton cloth, lightly moistened with a recognized cleaning product for medical equ

LCD panel94LCD panelIt may be possible that dust particles have entered the display and are stuck behind the front glass.We recommend to let this clea

LCD panel95Figure 29To clean the LCD panel:• Take care not to touch the I-guard light sensor on the LCD panel.• Dust particles on the LCD panel may be

LCD panel(This page intentionally left blank.)96

97Troubleshooting

Troubleshooting(This page intentionally left blank.)98(This page intentionally left blank.)

General tips99General tips• If one display from a multi-head system exhibits problems, try to eliminate the problem by switching video cables or power