SLite DisplayService manualR5976621/0202/09/2005
2. General informationHDFGFEImage 2-3• D.LEDassembly.• E. Controller unit.• F. Small fan SMPS assembly.• G. Power distribution unit.• H. SMPS unit.IJK
2. General information2.3 Internal wiring diagramDiagramInternal wiring between LED drivers, controller and power distribution unit (seen from the bac
2. General informationFan interconnectionsImage 2-62.4 Startup sequence of an SL ite display systemThe first two steps of the startup sequence are don
2. General information8. The LED driver receives data from the controller.- The yellow LED on the LED drivers goes on.9. The SLite tile shows video co
2. General information10 R5976621 SLITE DISPLAY 02/09/2005
3. Spare part and service kits for SLite displays3. SPARE PART AND SERVICE KITS FOR SLITEDISPLAYS3.1 Spare part and service kitsGeneral:Barco provides
3. Spare part and service kits for SLite displays12 R5976621 SLITE DISPLAY 02/09/2005
4. Troubleshooting check list of an SLite tile4. TROUBLESHOOTING CHECK LIST OF AN SLITE TILEOverview• No image on an SLite display• No image on an SLi
4. Troubleshooting check list of an SLite tile4.2 No image on an SLite tile.Check list:Situation SolutionSLite tile has no power.1. Plug in the power
4. Troubleshooting check list of an SLite tileSituation SolutionThe SLite SMPS has “hiccups”.SMPS tries to start up but fails repeatedlydue to a short
Barco nv EventsNoordlaan 5, B-8520 KuurnePhone: +32 56.36.89.70Fax: +32 56.36.88.24E-mail:[email protected] us at the web: www.barco.comPrintedinB
4. Troubleshooting check list of an SLite tile4.4 No image on half SLite LED boardCheck list:Situation SolutionThe factory calibration values in theme
4. Troubleshooting check list of an SLite tileCheck list:Situation SolutionMessage displayed repeatedly:!!!!FANFAIL1. Check if all fans are connected
4. Troubleshooting check list of an SLite tile18 R5976621 SLITE DISPLAY 02/09/2005
5. On Screen Display messages5. ON SCREEN DISPLAY MESSAGESGeneralAn SLite tile can generate and display several “On Screen Display” (OSD) messages reg
5. On Screen Display messagesOSDmessageDescriptionVPOS146→194Displaying the start pixel column and end pixel column of the tile in the complete LED-wa
5. On Screen Display messagesOSDmessageDescriptionRS232SPEED57600baudDisplaying the current RS232 speed which value is set to 57600 baud.The baud rate
5. On Screen Display messagesOSDmessageDescriptionCALIFULLINDIVBASEDDisplaying calibration status: Both corrections, luma (white balance) and color (R
5. On Screen Display messagesOSDmessageDescriptionTEMP.I2C-ERRORI2C error occurred while reading the temperature value of the tile.RUNTIMEI2C-ERRORI2C
5. On Screen Display messages24 R5976621 SLITE DISPLAY 02/09/2005
6. Servicing an SLite tile6. SERVICING AN SLITE TILE6.1 Replace the re-sync unit of an SLite tileHow to replace the re-sync unit of an SLite tile ?1.
ChangesBarco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war-rant
6. Servicing an SLite tile6.4 Replace the controller unit of an SLite tileHow to replace the controlle r unit of an SLit e t ile ?1. Ensure you unders
6. Servicing an SLite tile5. Place a new fan, see "Install a fan on the SMPS assembly", page 43.6. Place the SMPS assembly with the new fan
6. Servicing an SLite tile28 R5976621 SLITE DISPLAY 02/09/2005
7. SLite servicing procedures7. SLITE SERVICING PROCEDURES7.1 Remove t he resync-unit of an SLite tileNecessary toolsNut driver 10 mmHow to remove the
7. SLite servicing proceduresCAUTION: Always replace the old sealing ring of the re-sync unit with a new one for each time the re-syncunit is removed.
7. SLite servicing proceduresImage 7-4Nuts to release for removing the back cover.3. Remove the back cover about 40 cm, away from the tile, in horizon
7. SLite servicing procedures6. Gently lower down the back cover and let the weight of the back cover be carried by the two belts between the tile and
7. SLite servicing procedures6. Place the back cover into position and fasten with 14 bolts, using a 13 mm nut driver.7.5 Remove the SMPS assembly of
7. SLite servicing proceduresImage 7-107.6 Install the SMPS a ssembly of an SLite tileNecessary toolsNut driver 7 mmHow to install the SMPS assembly o
7. SLite servicing procedures3. Connect a safety cable with safety hooks between the eyelid on the LED driver and the eyelid attached inside the frame
7. SLite servicing procedures5. Remove the LED assembly. Push forward, rotate and pull backwards.Image 7-1512Image 7-166. Remove the safety cable betw
7. SLite servicing proceduresHowtoinstallaLEDassemblyinanSLitetile?1. Place a new sealing ring on the LED assembly. Ensure the rubber position pins on
7. SLite servicing proceduresImage 7-197.10 Install the controller unit of an SLite tileNecessary toolsNut driver 7 mmHow to install the controller un
7. SLite servicing proceduresImage 7-203. Remove the two M4 nuts at the left side of the power distribution unit, using a 7 mm nut driver.BOARD TO BOA
7. SLite servicing procedures7.12 Install the power distribution unit of an SLite tileNecessary tools• Nut driver 7 mm• Torx driver T20How to install
7. SLite servicing procedures3. Release the 7 torx head screws.Image 7-254. Pull out the SMPS unit from the SMPS assembly.7.14 Install the SMPS unit o
7. SLite servicing procedures7.15 Manual startup of the SMPS unitWhy starting up the SMPS unit manually ?To determine the cause of a malfunction SLite
7. SLite servicing procedures7.17 Install a fan on the SMPS assemblyNecessary tools• Ballpoint Allen key 3 mm• Nut driver 7 mmHow to install a fan on
7. SLite servicing proceduresAABCDBBCDBImage 7-28A Lifting eye bolt.B SLite attachment bolt.C SLite side handle.D SLite rear handle.Image 7-296.The pe
7. SLite servicing proceduresImage 7-32 Image 7-33R5976621 SLITE DISPLAY 02/09/2005 45
Table of contentsTABLE OF CONTENTS1. Safety...
7. SLite servicing procedures46 R5976621 SLITE DISPLAY 02/09/2005
8. Maintenance8. MAINTENANCE8.1 Cleaning SLite tilesWhy clean SLite t iles ?Due to outdoor use the SLite tiles are exposed to all kinds of weather con
8. Maintenance48 R5976621 SLITE DISPLAY 02/09/2005
IndexINDEXBBack cover 30, 32Board location 5CCleaning 47SLite tiles 47Controller 37–38Controller unit 26DDimensions 5FFan 26Fan fail 16Fan location 5F
Table of contents2 R5976621 SLITE DISPLAY 02/09/2005
1. Safety1. SAFETY1.1 Servicing safety instructionsWARNING: Servicing must be done by authorized and qualified technical personnel only, which are tho
1. Safety4 R5976621 SLITE DISPLAY 02/09/2005
2. General information2. GENERAL INFORMATION2.1 SLite tile dimensionsDimensions896672560189,6253,7710Image 2-1Dimensions given in millimeters.2.2 Boar
Commentaires sur ces manuels